Ryobi Electric Pressure Washer Troubleshooting

Are you looking for how to troubleshooting Ryobi pressure washer?

Ryobi is the first name in the electric pressure washer manufacturers industry.

This leading company builds undoubtedly the best electric pressure washers for sale.

Even these washers last longer without any problems. However, there is an unspoken truth, “electric and electronic devices face repairing after some time.”

When you are facing different types of issues in your washer, you don’t need to worry.

Unplug the device from the power source. Then follow these Ryobi electric pressure washer troubleshooting tips:

Problem: Electric Pressure Washer Won’t Start

Causes

1. On-off switch error
2. Extension cord damage
3. Lack of sufficient power
4. Tripped pressure washer circuit breaker.

Ryobi pressure washer troubleshooting

• Check the switch if there is any damage. Even you should inspect the position of the switch whether it’s in the correct place or not. If the switch is causing trouble, change or set up a new switch.

• When the cord is more extended than the required length, the machine won’t react appropriately. Buy standard length cord such as 25’ or 50’ gauge cord. I recommend you not to use torn or damaged wire.

• Change the power outlet, and you will see the improvement.

• Shut down the device and wait for at least 30 minutes. After cooling the Ryobi pressure washer, restart it.

Problem: Insufficient Pressure

Causes

1. Small garden hose
2. Restricted water supply
3. Clogged water inlet filter
4. Air-suction in the pump

Ryobi pressure washer troubleshooting

• You should change the hose size. 1” or 5/8” would be better as a replacement.

• Open the water source completely. Look for the leakage or any blockage.

• After repetitive uses, the water inlet filter gets clogged. It is familiar to each electric pressure washer. You should remove the filter and clean it. Rinse the filter with warm water and let it dry.

• Tighten all the fittings and hose connections. Try to pull the trigger on the spray gun. Then there will be a flow of water that runs through the pressure washer nozzle.

Problem: Output Pressure Fluctuation

Causes

1. Insufficient inlet water supply
2. Air-suction in the pump
3. Discharge nozzle error
4. Solidified gun, hose, or power nozzle

Ryobi pressure washer troubleshooting

• You should turn on the faucet completely. If there is leakage, repair it.

• Tighten all the fittings and hose connections. Try to pull the trigger on the spray gun. Then there will be a flow of water that runs through the pressure washer nozzle.

• Use a needle to blow out the dirt or debris from the discharge nozzle.

• Pour some distilled vinegar in the detergent container.

Problem: Noisy Pump

Causes

1. Air is travelling through the pump
2. Clogged water inlet filter

Ryobi pressure washer troubleshooting

• Tighten all the fittings and hose connections. Try to pull the trigger on the spray gun. Then there will be a flow of water that runs through the pressure washer nozzle.

• You should remove the filter and clean it. Rinse the filter with warm water and let it dry.

Problem: Water and Oil Leakage From The Pump

Causes

1. Fitting issues
2. Damaged or worn water seals
3. Broken oil seals

Ryobi pressure washer troubleshooting

• First, check all the fittings. Tighten them properly to prevent water leakage.

• Contact the seller or manufacturer support. They will care about the water seal.

• Use a sealant to seal the oil container. If it seems harsh, contact the manufacturer.

Problem: Motor Starts But Running Failure

Causes

1. Low supply voltage
2. Loss of voltage
3. Residual pressure in the unit
4. Residual friction

Ryobi pressure washer troubleshooting

• You should avoid using other devices on the same circuit. Multiple devices can lower the supply voltage below the minimum requirement.

• Check if the extension cord is damaged. You can also remove the extension cord and plug in the Ryobi pressure washer directly to the power outlet.

• After turning the device off, pull the trigger on the sprayer. It will release pressure. Then switch on the device.

• First, disconnect the water supply. Then turn on the machine for 2 to 3 seconds. You can repeat this process a couple of times. Then the motor will start properly.

Recommended: Pressure washer soap, Pressure washer surface cleaner

Troubleshooting an Electric Pressure Washer

Final Talks

Ryobi electric pressure washer troubleshooting is not a tough thing to do.

These above are simple to do on your own. You should attempt them carefully to avoid any accidents.

Sale

Ryobi 1,600-PSI 1.2-GPM Electric Pressure Washer (Model RY141612)

• Brand New in box; The product ships with all relevant accessories
• Brand new and boxed Product ships with all relevant accessories
• Spray wand with nozzle quick connect coupler

Check Price Now

Now, It’s Over To You!

Now I’d like to hear from you: Leave a comment to let me know.

Spread it by Sharing on social media…